Graco Inc Thermostat 233757 User Manual

Instructions/Parts List  
Low Pressure  
309474K  
Fluid Regulators  
EN  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
Model 233757 Shown  
II 2 G  
 
List of Models  
List of Models  
Fluid Pressure Regulators  
Part No.  
Series Model  
Type  
Maximum Fluid Inlet Pressure Regulated Pressure Range  
233757  
234263  
B
B
P20-VM  
P20-VM npt  
Mechanical,  
fluid pressure  
580 psi (4000 kPa, 40 bar)  
1015 psi (7000 kPa, 70 bar)  
580 psi (4000 kPa, 40 bar)  
580 psi (4000 kPa, 40 bar)  
580 psi (4000 kPa, 40 bar)  
15-290 psi  
(100-2000 kPa, 1-20 bar)  
233759  
234267  
B
B
P50-VM  
P50-VM npt  
Mechanical,  
fluid pressure  
145-725 psi  
(1000-5000 kPa, 10-50 bar)  
233773  
234272  
B
B
P10-VP  
P10-VP npt  
Pneumatic,  
fluid pressure  
6-145 psi  
(40-1000 kPa, 0.4-10 bar)  
233774  
234273  
B
B
P10-VM  
P10-VM npt  
Mechanical,  
fluid pressure  
15-145 psi  
(100-1000 kPa, 1-10 bar)  
233809  
234256  
B
B
P10-VP, OEM  
P10-VP, OEM npt fluid pressure  
Pneumatic,  
6-145 psi  
40-1000 kPa, 0.4-10 bar)  
Back Pressure Regulators  
Maximum Permanent Supply  
Pressure  
Part No.  
Series Model  
Type  
Regulated Pressure Range  
233758  
234262  
B
B
P10-RM  
P10-RM npt  
Mechanical,  
back pressure  
145 psi (1000 kPa, 10 bar)  
145 psi (1000 kPa, 10 bar)  
290 psi (2000 kPa, 20 bar)  
725 psi (5000 kPa, 50 bar)  
290 psi (2000 kPa, 20 bar)  
15-145 psi  
(100-1000 kPa, 1-10 bar)  
233810  
234257  
B
B
P10-RP  
P10-RP npt  
Pneumatic,  
back pressure  
15-145 psi  
(100-1000 kPa, 1-10 bar)  
233811  
234255  
B
B
P20-RM DN13  
P20-RM DN13 npt back pressure  
Mechanical,  
29-290 psi  
(200-2000 kPa, 2-20 bar)  
233812  
234258  
B
B
P50-RM  
P50-RM npt  
Mechanical,  
back pressure  
73-725 psi  
(500-5000 kPa, 5-50 bar)  
233950  
234261  
B
B
P20-RM DN1  
P20-RM DN1 npt back pressure  
Mechanical,  
15-290 psi  
(100-2000 kPa, 1-20 bar)  
Key to Model Designation  
Pressure regulation valve e.g. P20- R  
M
DN13 npt  
npt version  
Valve Seat Orifice 13mm  
Operating Mode  
P - pneumatic  
M - mechanical  
Action  
V - pressure regulation  
R - back-pressure regulation  
Regulation max  
20 bar  
309474K  
3
 
 
Warning  
WARNING  
EQUIPMENT MISUSE HAZARD  
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.  
This equipment is for professional use only.  
Read all instruction manuals, tags, and labels before operating the equipment.  
Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.  
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.  
Check equipment daily. Repair or replace worn or damaged parts immediately.  
Do not exceed the maximum working pressure of the lowest rated system component. Refer to the  
Technical Data on page 20 for the maximum working pressure of this equipment.  
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Techni-  
cal Data section of all equipment manuals. Read the fluid and solvent manufacturer's warnings.  
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose  
Graco hoses to temperatures above 180°F (82°C) or below -40°F (-40°C).  
Wear hearing protection when operating this equipment.  
Never use 1,1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or  
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a  
chemical reaction, with the possibility of explosion.  
Comply with all applicable local, state, and national fire, electrical, and safety regulations.  
4
309474K  
 
 
Warning  
WARNING  
PRESSURIZED EQUIPMENT HAZARD  
Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin and  
cause serious injury.  
Do not point the gun at anyone or at any parts of the body.  
Do not stop or deflect leaks with your hand, body, glove, or rag.  
Follow the Pressure Relief Procedure on page 11 whenever you are instructed to relieve pressure;  
stop spraying; clean, check, or repair the equipment; and install or clean the spray nozzle.  
Tighten all fluid connections before operating the equipment.  
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.  
Permanently coupled hoses cannot be repaired; replace the entire hose.  
TOXIC FLUID HAZARD  
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,  
inhaled, or swallowed.  
Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.  
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,  
state and national guidelines.  
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and  
solvent manufacturer.  
309474K  
5
 
 
Introduction  
Introduction  
A fluid pressure regulator is used in air spray systems to  
ensure accurate, positive control of fluid pressure to an  
air spray gun or to a low pressure dispensing valve or  
atomizing head.  
Fluid Pressure Regulators  
Models 233757, 233759, 233774, 234263, 234267, and  
234273 (FIG. 2.) are mechanically operated fluid pres-  
sure regulators designed primarily for use with low to  
medium viscosity fluids.  
A regulator installed at a circulating line take-off or pump  
reduces main line pressure to maintain the desired fluid  
pressure to the air spray gun or to a low pressure dis-  
pensing valve or atomizing head.  
Models 233773, 233809, 234256, and 234272 (FIG. 3.)  
are pneumatically operated fluid pressure regulators  
designed primarily for use with highly viscous coatings.  
Back Pressure Regulators  
Models 233810, 233811, 233812, 233950, 234255,  
234257, 234258, 233758, 234261, and 234262, are  
back pressure regulators that limit the supply pressure  
to a set value by opening an outlet and guiding back  
excess material when the predetermined pressure has  
been achieved. These valves are used in circulating  
systems. Model 233810 pneumatic back pressure regu-  
lator is shown in FIG. 1.  
Air inlet  
Piston  
Fluid Inlet  
(from gun)  
Fluid Outlet  
Diaphragm  
(return line)  
Valve plunger  
TI1773A  
Fig. 1. Cutaway of Pneumatic Back Pressure Regulator  
6
309474K  
 
     
Introduction  
Adjustment screw  
Spring  
Diaphragm  
Fluid Outlet  
(to gun)  
Fluid Inlet  
(from pump)  
Valve plunger  
Valve ball and seat  
2 A  
TI1772B  
Fig. 2. Cutaway of Mechanical Fluid Pressure Regulator  
Air inlet  
Fluid Inlet  
(from pump)  
Fluid Outlet  
(to gun)  
Diaphragm  
Valve plunger  
Valve ball and seat  
TI1771B  
7 1 A  
Fig. 3. Cutaway of Pneumatic Fluid Pressure Regulator  
309474K  
7
 
Installation  
Installation  
1. Install one regulator for each spray gun.  
b. Install a back pressure regulator downstream of  
the gun. Connect the fluid return line from the  
gun to the inlet of the back pressure regulator.  
Connect the fluid return line to the pump to the  
regulator’s outlet.  
2. Apply thread sealant to connections as necessary.  
3. Make sure that the direction of fluid flow agrees with  
the flow direction markings on the regulator body.  
a. Install a fluid pressure regulator upstream of the  
gun: Connect the fluid line from the pump to the  
inlet of the fluid regulator. Connect the fluid line  
to the gun to the regulator’s outlet.  
4. Flush and test the entire system.  
FIG. 4., FIG. 5., and FIG. 6. show possible configurations  
for installing a system. They do not depict actual system  
designs. Consult your Graco distributor for assistance in  
designing a system that meets your specific require-  
ments.  
B
A
F
Air to pump  
C
B
Air to gun  
Fluid  
Y
E
D
TI1767A  
Fig. 4. Low pressure, non-circulating system, mechanical fluid regulator  
Key  
E
F
Y
Fluid regulator  
A
B
C
D
Air line filter  
Air spray gun  
Bleed-type air shut-off valve  
Air regulator for pump and gun  
Pump  
Pump ground wire  
8
309474K  
 
 
Installation  
A
B
G
A
B
F
Air to Fluid  
Regulator  
Air to  
Pump  
C
B
Air to  
Gun  
Y
E
D
TI1766A  
Fig. 5. Low pressure, non-circulating system, pneumatic fluid regulator  
Key  
E
F
Fluid regulator  
A
B
C
D
Air line filter  
Air spray gun  
Bleed-type air shut-off valve  
Air regulator for pump and gun  
Pump  
G
Y
Air regulator for fluid regulator  
Pump ground wire  
309474K  
9
 
Installation  
A
A
A
Air  
B
F
B
B
Fluid  
C
G
K
Air to  
gun  
Air to Fluid  
Regulator  
Air to Back  
Pressure  
Fluid  
Regulator  
E
H
J
Fluid  
to gun  
Fluid return from gun  
TI1768A  
Fig. 6. Low Pressure circulating system, pneumatic fluid regulator and back pressure regulator  
Key  
G
H
J
Air regulator for fluid regulator  
Fluid shutoff valve  
A
B
C
E
F
Air line filter  
Bleed-type air shut-off valve  
Air regulator for pump and gun  
Fluid regulator  
Back pressure regulator  
K
Y
Air regulator for back pressure regulator  
Pump ground wire  
Air spray gun  
10  
309474K  
 
Operation  
Operation  
Mechanical Regulator  
Flush Before First Use  
1. Back out the adjustment screw until there is no  
spring pressure.  
Your pressure regulator has been tested in the factory  
with an anti-corrosion liquid. Before using the regulator,  
thoroughly flush the system with a solvent to remove  
residue of this liquid as well as any contaminants that  
have been introduced during assembly of the system.  
2. Turn on the fluid supply, to admit fluid to the regula-  
tor.  
3. Turn the screw clockwise to adjust fluid pressure to  
the desired level.  
Pressure Relief Procedure  
Pneumatic Regulator  
1. With the fluid supply shut off, turn on the air pres-  
sure to the regulator.  
WARNING  
2. Turn on the fluid supply, to admit fluid to the regula-  
tor.  
Read the warnings on page 5, and follow the Pressure  
Relief Procedure below whenever you:  
3. Increase the fluid inlet pressure. When the fluid out-  
let pressure is at the desired level, shut off the air to  
the fluid regulator.  
are instructed to relieve pressure  
stop spraying  
check or service any of the equipment  
install or clean the fluid nozzle.  
1. Shut off the air to the pump.  
2. Trigger the air spray gun to relieve the fluid pres-  
sure.  
3. Open the fluid drain valve to relieve all fluid pres-  
sure, having a container ready to catch the drain-  
age.  
Adjusting the Regulator  
The fluid pressure regulator controls pressure down-  
stream from its outlet. The inlet fluid pressure should  
always be higher than the outlet fluid pressure.  
If you are using an accessory fluid pressure gauge, trig-  
ger the air spray gun to relieve pressure in the line when  
reducing the pressure, to ensure a correct gauge read-  
ing.  
Adjust the pump air pressure and the fluid pressure reg-  
ulator for the best spraying combination.  
In a circulating system, the back pressure valve controls  
the fluid pressure upstream of its inlet in the same way.  
309474K  
11  
 
       
Troubleshooting  
Troubleshooting  
Relieve the pressure (page 11) before checking or repairing the equipment.  
To repair the regulator, refer to page 13.  
Problem  
Cause  
Solution  
Replace diaphragm.  
Drop in fluid outlet pressure.  
Ruptured diaphragm (15).  
Air escaping (pneumatic regulators  
only).  
Check air hose and connections.  
Replace piston seal (21).  
Fluid outlet pressure increases to  
level of fluid inlet pressure.  
Valve ball (5) and seat (2) are worn  
or stuck open.  
Clean ball and seat. Replace worn or  
damaged parts.  
Fluid leaking from upper housing.  
Ruptured diaphragm (15).  
Replace diaphragm.  
12  
309474K  
 
 
Maintenance  
Maintenance  
1. Relieve all air and fluid pressure in the system.  
Flushing  
2. Remove the regulator from the system.  
Flush before changing colors, at the end of the day,  
before storing, and before repairing the equipment.  
3. Disassemble the regulator (see the parts drawings  
on pages 14 through 19).  
Flush with a fluid that is compatible with the fluid you are  
pumping and with the wetted parts of your system.  
Check with your fluid manufacturer or supplier for rec-  
ommended flushing fluids and flushing frequency.  
Relieve the pressure after flushing.  
4. Clean and inspect all parts.  
CAUTION  
Do not allow paint or solvent to sit in the system for  
extended periods. Fluid could dry in the regulator and  
cause leakage. If leakage occurs, relieve pressure, then  
disassemble and clean the regulator.  
Be very careful when handling the carbide balls and  
seats. Damage will cause poor operation and leak-  
age.  
5. Inspect the diaphragm, packings, o-rings, and seals  
for wear. Check the ball and seat for nicks, wear, or  
other damage.  
Cleaning and Repair  
When changing fluids or colors, the regulator should be  
disassembled and cleaned. Regular cleaning and  
inspection of the internal parts is necessary to keep the  
fluid regulator working properly.  
6. Lubricate packings, o-rings and seals when reas-  
sembling the regulator.  
309474K  
13  
 
     
Parts  
Parts  
Mechanical Fluid Pressure Regulators  
Part Nos. 233759 and 234267  
25  
1
6
17  
15  
28  
26  
27  
3
14  
2
10  
5
24  
3
4
22  
1
21  
13  
12  
10  
5
20  
5
6
7
4
8
19  
18  
11  
2
1
2
3
5
6
Torque to 6 N•m (53 in-lb).  
Torque to 2 N•m (18 in-lb).  
Fill internal cavity with grease.  
Used only on non-npt model 233759.  
Torque to 5 N•m (44in-lb).  
TI1753A  
23  
16  
9
Ref.  
Ref.  
No. Part No. Description  
No. Part No. Description  
Qty  
Qty  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
245372  
15A179  
15A173  
117122  
15A175  
117096  
117092  
15A176  
117105  
15A186  
245366  
117129  
117017  
15A141  
15A242  
PLUNGER, valve  
DIAPHRAGM  
CAP, spring  
1
1
1
1
1
1
1
1
1
1
1
8
8
1
1
1
HOUSING, lower, for 233759  
HOUSING, lower, for 234267  
SEAT, valve  
O-RING  
O-RING  
BALL, 6 mm, carbide  
SUPPORT, ball  
SPRING, compression  
COVER  
SCREW, fhms, M4x10  
RING, for non-npt model 233759  
only  
1
1
1
1
2
1
1
1
1
2
2
2
3
4
5
6
7
8
9
245368  
15Y036  
15Y035  
117106  
15A205  
117090  
15A144  
117123  
15A219  
NUT, seal-lock  
PLATE, spring, bottom  
SPRING, compression  
SPRING, compression  
PLATE, spring, top  
BALL, 6 mm  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x80  
WASHER  
10  
11  
12  
13  
117101  
117085  
117099  
PLUG, threaded  
SEAL, ring  
PLUG, threaded  
2
1
1
BONNET, cover  
SCREW, custom  
14  
309474K  
 
   
Parts  
Mechanical Back Pressure Regulators  
Part Nos. 233812 and 234258  
25  
1
17  
15  
6
28  
26  
27  
3
14  
2
10  
5
24  
3
4
22  
1
21  
13  
12  
10  
5
20  
4
8
19  
18  
11  
2
1
2
3
5
6
Torque to 6 N•m (53 in-lb).  
Torque to 2 N•m (18 in-lb).  
Fill internal cavity with grease.  
9
23  
16  
Used only on non-npt model 233812.  
Torque to 5 N•m (44in-lb).  
TI11248a  
Ref.  
No. Part No. Description  
Ref.  
No. Part No. Description  
Qty  
Qty  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
15A179  
15A173  
117122  
15A175  
117096  
117092  
15A176  
117108  
15A186  
245366  
117129  
117017  
15A141  
15A242  
DIAPHRAGM  
CAP, spring  
NUT, seal-lock  
1
1
1
1
1
1
1
1
1
1
8
8
1
1
1
HOUSING, lower, for 233812  
HOUSING, lower, for 234258  
SEAT, valve  
O-RING  
O-RING  
1
1
1
1
2
1
2
2
2
3
4
8
9
10  
245369  
15Y036  
15Y035  
15A143  
117123  
15A219  
PLATE, spring, bottom  
SPRING, compression  
SPRING, compression  
PLATE, spring, top  
BALL, 8 mm  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x80  
WASHER  
COVER  
SCREW, fhms, M4x10  
RING, for non-npt model 233812  
only  
11  
12  
13  
14  
117101  
117085  
117099  
245373  
PLUG, threaded  
SEAL, ring  
PLUG, threaded  
PLUNGER, valve  
2
1
1
1
BONNET, cover  
SCREW, custom  
309474K  
15  
 
 
Parts  
Mechanical Fluid Pressure Regulators  
Part Nos. 233757, 233774, 234263, and 234273  
28  
15  
25  
24  
1
14  
2
10  
5
3
4
22  
21  
1
13  
12  
11  
19  
10  
5
17  
16  
3
5
6
7
1
2
3
4
5
Torque to 4-5 N•m (35-44 in-lb).  
Torque to 2 N•m (18 in-lb).  
2
4
4
8
9
Torque to 5 N•m (44 in-lb).  
TI1751A  
23  
Grease OD.  
Used only on non-npt models 233757 and 233774.  
Ref.  
Ref.  
No. Part No. Description  
No. Part No. Description  
Qty  
Qty  
13  
14  
15  
16  
17  
19  
117099  
245372  
15A179  
15A172  
117122  
117087  
PLUG, threaded  
PLUNGER, valve  
DIAPHRAGM  
CAP, spring  
NUT, seal-lock  
SPRING, compression, for 233774  
and 234273  
SPRING, compression, for 233757  
and 234263  
PLATE, spring, top  
BALL, 6 mm  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x16  
SCREW, custom  
1
1
1
1
1
1
1
HOUSING, lower, for 233757 and  
233774  
1
HOUSING, lower, for 234263 and  
234273  
1
2
3
4
5
6
7
8
9
245368  
15Y036  
15Y035  
117106  
15A205  
117090  
15A144  
117123  
15A219  
SEAT, valve  
O-RING  
O-RING  
BALL, 6 mm, carbide  
SUPPORT, ball  
1
1
2
1
1
1
1
2
2
117095  
1
21  
22  
23  
24  
25  
28  
15A177  
117105  
15A185  
245365  
117126  
15A241  
1
1
1
1
8
1
SPRING, compression  
COVER  
SCREW, fhms, M4x10  
RING, for non-npt models 233757  
and 233774 only  
PLUG, threaded  
SEAL, ring  
10  
11  
12  
117101  
117085  
2
1
16  
309474K  
 
 
Parts  
Mechanical Back Pressure Regulators  
Part Nos. 233758, 233811, 233950, 234255, 234261, and 234262  
28  
15  
14  
25  
1
24  
2
3
10  
5
6
4
22  
21  
1
1
2
3
4
5
13  
12  
Torque to 4-5 N•m (35-44 in-lb).  
Torque to 2 N•m (18 in-lb).  
Torque to 5 N•m (44 in-lb).  
Grease OD.  
10  
5
19  
17  
16  
3
11  
8
6
2
4
Used only on non-npt models  
233758, 233950, and 233811.  
4
7
6
7
Not used on models 233811 and  
234255.  
9
6
23  
Models 233811 and 234255 use a  
plug and retaining ring (not shown).  
TI11249a  
Ref.  
No. Part No. Description  
Ref.  
No. Part No. Description  
Qty  
Qty  
11  
117101  
PLUG, threaded, not used on mod-  
els 233811 and 234255  
SEAL, ring  
2
1
HOUSING, lower, for 233758 and  
233950  
1
12  
13  
14  
117085  
117099  
245373  
1
1
1
HOUSING, lower for 234262 and  
234261  
1
PLUG, threaded  
PLUNGER, valve, for 233758,  
233950, 234261, and 234262  
PLUNGER, valve, for 233811 and  
234255  
15A198  
15C303  
245369  
HOUSING, lower, for 233811  
HOUSING, lower, for 234255  
SEAT, valve, for 233758, 233950,  
234261, and 234262  
1
1
1
245378  
1
2
15  
16  
17  
19  
15A179  
15A172  
117122  
117087  
DIAPHRAGM  
CAP, spring  
NUT, seal-lock  
SPRING, compression, for 233758  
and 234262  
1
1
1
1
15A228  
15Y036  
15Y035  
SEAT, valve, for 233811 and  
234255  
O-RING, not used on models  
233811 and 234255  
O-RING, for 233758, 233950,  
234261, and 234262  
1
1
2
3
4
117095  
SPRING, compression, for 233811,  
233950, 234261, and 234255  
PLATE, spring, top  
BALL, 6 mm  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x16  
SCREW, custom  
RING, retaining, 233811 and  
234255 only  
1
15Y031  
15A143  
O-RING, for 233811 and 234255  
COVER, for 233758, 233950,  
234261, and 234262  
2
1
21  
22  
23  
24  
25  
28  
29  
15A177  
117105  
15A185  
245365  
117126  
15A241  
117124  
1
1
1
1
8
1
1
8
15A222  
117123  
PLUG, for 233811 and 234255  
SCREW, fhms, M4x10, not used on  
models 233811 and 234255  
RING, for non-npt models 233758,  
and 233950  
1
2
9
10  
15A219  
15A221  
2
2
RING, for non-npt model 233811  
309474K  
17  
 
 
Parts  
Pneumatic Fluid Pressure Regulators  
Part Nos. 233773, 233809, 234272, and 234256  
1
2
3
4
5
26  
Torque to 4-5 N•m (35-44 in-lb).  
Torque to 2 N•m (18 in-lb).  
Torque to 5 N•m (44 in-lb).  
Grease OD.  
6
25  
1
27  
6
14  
2
24  
Used only on non-npt models  
233773 and 233809.  
6
Used only on npt models  
234272 and 234256.  
17  
3
3
4
10  
5
21  
1
16  
4
12  
13  
10  
5
23  
5
11  
6
7
2
15  
4
8
9
TI1755A  
Ref.  
No.  
Ref.  
No.  
Part No. Description  
Qty.  
Part No. Description  
HOUSING, lower, for 233773 and  
Qty.  
9
10  
117123  
15A219  
SCREW, fhms, M4x10  
RING, for non-npt models 233773  
2
2
1
1
233809  
and 233809  
HOUSING, lower, for 234272 and  
234256  
1
1
1
11  
12  
13  
14  
15  
16  
17  
21  
23  
24  
25  
26  
117101  
117085  
117099  
245372  
15A179  
15A204  
117122  
117102  
15A185  
15A191  
117127  
15C332  
PLUG, threaded  
SEAL, ring  
PLUG, threaded  
PLUNGER, valve  
DIAPHRAGM  
PISTON  
NUT, seal-lock  
SEAL, flat  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x35  
FITTING, for npt models 234272  
and 234256 only  
WASHER, for npt models 234272  
and 234256 only  
2
1
1
1
1
1
1
1
1
1
8
1
2
245368  
245371  
SEAT, valve, for 233773 and  
234272  
SEAT, valve, for 233809 and  
234256  
3
4
5
15Y036  
15Y035  
117106  
O-RING  
O-RING  
1
1
1
BALL, 6 mm, carbide, for 233773  
and 234272  
117110  
BALL, 6 mm, for 233809 and  
234256  
1
6
7
8
15A205  
117090  
15A144  
SUPPORT, ball  
SPRING, compression  
COVER  
1
1
1
27  
15C333  
1
18  
309474K  
 
 
Parts  
Pneumatic Back Pressure Regulators  
Part Nos. 233810 and 234257  
26  
6
25  
1
27  
6
14  
2
24  
17  
3
3
4
10  
5
21  
1
16  
4
12  
13  
10  
5
23  
1
2
3
4
5
6
Torque to 4-5 N•m (35-44 in-lb).  
Torque to 2 N•m (18 in-lb).  
Torque to 5 N•m (44 in-lb).  
Grease OD.  
4
8
11  
2
15  
9
Used only on non-npt model 233810.  
Used only on npt model 234257.  
TI11250a  
Ref.  
No.  
Ref.  
No.  
Part No. Description  
Qty.  
Part No. Description  
HOUSING, lower, for 233810  
Qty.  
15  
16  
17  
21  
23  
24  
25  
26  
15A179  
15A204  
117122  
117102  
15A185  
15A191  
117127  
15C332  
DIAPHRAGM  
PISTON  
NUT, seal-lock  
SEAL, flat  
PACKING, PTFE with carbon  
HOUSING, upper  
SCREW, shcs, M5x35  
FITTING, for npt model 234257  
only  
1
1
1
1
1
1
8
1
1
1
1
1
1
1
1
2
2
2
1
1
1
HOUSING, lower, for 234257  
SEAT, valve  
2
3
4
8
245369  
15Y036  
15Y035  
15A143  
117123  
15A219  
117101  
117085  
117099  
245373  
O-RING  
O-RING  
COVER  
9
SCREW, fhms, M4x10  
RING, for non-npt model 233810  
PLUG, threaded  
SEAL, ring  
10  
11  
12  
13  
14  
27  
15C333  
WASHER, for npt model 234257  
only  
1
PLUG, threaded  
PLUNGER, valve  
309474K  
19  
 
 
Technical Data  
Technical Data  
Category  
Data  
Maximum Fluid Inlet Pressure  
(Fluid Pressure Regulators)  
233757, 233773, 233774, 233809,  
234256, 234263, 234272, 234273 : 580 psi (4000 kPa, 40 bar)  
233759, 234267: 1015 psi (7000 kPa, 70 bar)  
Maximum Permanent Supply Pres- 233758, 233810, 234257, 234262: 145 psi (1000 kPa, 10 bar)  
sure (Back Pressure Regulators)  
233811, 233950, 234255, 234261: 290 psi (2000 kPa, 20 bar)  
233812, 234258: 725 psi (5000 kPa, 50 bar)  
Pressure Range  
233773, 233809, 234272, 234256: 6-145 psi (40-1000 kPa, 0.4-10 bar)  
233758, 233774, 233810,  
234257,234262, 234273 : 15-145 psi (100-1000 kPa, 1-10 bar)  
233757, 234263: 15-290 psi (100-2000 kPa, 1-20 bar)  
233811, 233950, 234255, 234261: 29-290 psi (200-2000 kPa, 2-20 bar)  
233812, 234258: 73-725 psi (500-5000 kPa, 5-50 bar)  
233759, 234267: 145-725 psi (1000-5000 kPa, 10-50 bar)  
Maximum Operating Air Pressure 145 psi (1 MPa, 10 bar)  
(Pneumatic Regulators Only)  
Maximum Flow Rate  
Temperature Range  
See chart on page 21.  
233757, 233758, 233759, 233773, 233774, 233809, 233810, 233811, 233950,  
234255, 234256, 234261, 234262, 234263, 234273: 32-194°F (0-90°C)  
233812, 234258: 50-176°F (10-80°C)  
Fluid inlet and outlet  
233757, 233758, 233759, 233773, 233774,  
233809, 233810, 233812, 233950: 3/8 in. BSPP(F)  
234256, 234257, 234258, 234261,  
234262, 234263, 234267, 234272, 234273: 3/8 in. npt(f)  
233811: 1 in. BSPP(F)  
234255: 1 in. npt(f)  
Air inlet  
233773, 233809, 233810: 1/4 in. BSPP(F)  
234256, 234257, 234272: 1/4 in. npt(m)  
1/8 in. BSPP(F)  
*Gauge port  
Wetted Parts  
Stainless steel, tungsten carbide, PTFE, chemically resistant fluoroelastomer,  
PEEK (233809 and 234256 only)  
* Accessory gauges available.  
20  
309474K  
 
 
Accessory Gauges  
Accessory Gauges  
Part No. Gauge  
Part No. Gauge  
233758  
234262  
233950  
234261  
233811  
234255  
233812  
234258  
233810  
234257  
118338  
118338  
118338  
118338  
118338  
118338  
118339  
118339  
118338  
118338  
233774  
243273  
233757  
234262  
233759  
234267  
234773  
234272  
233809  
234273  
118338  
118338  
118338  
118338  
118339  
118339  
118338  
118338  
118338  
118338  
Flow Rate Data  
Maximum fluid flow with 10 weight oil, regulator wide open and no downstream restrictions.  
Part No.  
Inlet Fluid Test Pressure  
Inlet/Outlet Size  
Seat Size  
Fluid Flow  
233757  
234263  
233758  
234262  
580 psi (4000 kPa, 40 bar)  
3/8 BSPP(F)  
3/8 npt(f)  
3/8 BSPP(F)  
3/8 npt(f)  
5 mm  
7.0 gpm (26.6 lpm)  
4.6 gpm (17.5 lpm)  
9.8 gpm (37.2 lpm)  
7.0 gpm (26.6 lpm)  
7.0 gpm (26.6 lpm)  
7.0 gpm (26.6 lpm)  
4.6 gpm (17.5 lpm)  
7.8 gpm (29.6 lpm)  
11.5 gpm (43.7 lpm)  
5.7 gpm (21.7 lpm)  
145 psi (1000 kPa, 10 bar)  
1015 psi (7000 kPa, 70 bar)  
580 psi (4000 kPa, 40 bar)  
580 psi (4000 kPa, 40 bar)  
580 psi (4000 kPa, 40 bar)  
145 psi (1000 kPa, 10 bar)  
290 psi (2000 kPa, 20 bar)  
725 psi (5000 kPa, 50 bar)  
290 psi (2000 kPa, 20 bar)  
6.5 mm  
5 mm  
233759  
234267  
3/8 BSPP(F)  
3/8 npt(f)  
233773  
234272  
233774  
234273  
3/8 BSPP(F)  
3/8 npt(f)  
3/8 BSPP(F)  
3/8 npt(f)  
5 mm  
5 mm  
233809  
234256  
3/8 BSPP(F)  
3/8 npt(f)  
5 mm  
233810  
234257  
233811  
234255  
3/8 BSPP(F)  
3/8 npt(f)  
1 in. BSPP(F)  
1 in. npt(f)  
6.5 mm  
13 mm  
6.5 mm  
6.5 mm  
233812  
234258  
3/8 BSPP(F)  
1 in. npt(f)  
233950  
234261  
3/8 BSPP(F)  
1 in. npt(f)  
309474K  
21  
 
   
Mounting Dimensions  
Mounting Dimensions  
A
Part No.  
Thread  
Dimension A  
233757  
234263  
M5  
24 mm (0.95 in.)  
233758  
234262  
M5  
M5  
M5  
M5  
M5  
M5  
M5  
M5  
M5  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
36 mm (1.42 in.)  
24 mm (0.95 in.)  
24 mm (0.95 in.)  
233759  
234267  
233773  
234272  
233774  
234273  
233809  
234256  
233810  
234257  
233811  
234255  
233812  
234258  
233950  
234261  
22  
309474K  
 
 
Mounting Dimensions  
309474K  
23  
 
Graco Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs  
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
For the latest information about Graco products, visit www.graco.com.  
For patent information, see www.graco.com/patents.  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 309474  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 2002, Graco Inc. is registered to ISO 9001  
Revision K, September 2014  
 
 

Grizzly Sander H2881 User Manual
Grizzly Staple Gun H5626 7 User Manual
Haier Washer HWD D1000TXVE User Manual
Honeywell Thermostat B Q682 User Manual
Hotpoint Freezer CTF~GC User Manual
HP Hewlett Packard Computer Accessories 16047C User Manual
HTC Cell Phone SM TP001 0704 User Manual
Hunter Fan Air Cleaner 30240 User Manual
Husky Paint Sprayer Spray Gun User Manual
IBM Credit Card Machine OS User Manual